EE 101: Electrical & Electronics Workshop
Week # Experiment # Vero Board (Small) Breadboard Style Vero Board (Large) Breadboard Style Vero Board (Large) Line Style PCB PCB DIP Adapter Seven Segment Common Anode Alphanumeric Display 2SA684 Dot Matrix 2N3904 Male Rectangular Header (Short) Male Round Header Female Round Header Jumper Wires LED's Block Connector 74LS47 ULN2003A / ULN2803 74HC595 ATMEGA32 ATMEGA128 Solder Wick Resistors DIP Switch (4 bit) DIP Switch (8 bit) 7805
Picture    
Datasheet Download Download  Yellow Download
RGB Datasheet
Download Download Download  
  1 Introduction to Basic lab tools & equipment with demonstration                                                  
  2 How to use a Vero Board for simple Single Digit Seven Segment Display with Soldering 1#         1       2 2 Strips   1 Strip From Lab 1 2 1#         1 Through Hole (Available in Lab) 1   1
  3 Usage of 4x Seven Segments with BCD IC on Vero Board 1#         4       5 2 Strips   1 Strip From Lab 1 2 1#           Through Hole (Available in Lab) 1 1 1
  4 Soldering of Alpha-numeric x 6Display on Vero board with Dip Switches or Microcontroller Interface 2                 7 2 Strips   2 Strips From Lab 1 2   2
(ULN2003)
        Through Hole (Available in Lab) 1 1
  5 Soldering of Single Dot Matrix on Vero Board with Dip Switches   1           8   8 2 Strips   2 Strips From Lab 1 2   3 (ULN2003)         Through Hole (Available in Lab)   2
  6 Soldering of RGB Dot Matrix on Vero Board with Dip Switches   1           8   8 2 Strips   4 Strips From Lab 1 2   3 (ULN2803)         Through Hole (Available in Lab)   4
  7 Introduction to PCB Design Tool Altium and design of single layer PCB                                                  
  8 Introduction to Toner Transfer Method for PCB with Etching and Drilling                                                  
  9(a) 4x Seven Segment  PCB Single Layer (with vias)        6x4 cm   4       5 2 Strips   2 Strips For  Vias   1 1           Through Hole (Available in Lab) 1  
  9(b) Single  Dot Matrix PCB Single Layer (with vias)        8x6cm         1 8 2 Strips   3 Strips For  Vias   1   1         Through Hole (Available in Lab)   1
  10 (a) Introduction to two Layer PCB design and Fabrication with SMD Component (TO-92,  SOIC,  TSSOP) placement                                                  
  10(b) Single  Dot Matrix PCB Double Layer (with vias)        4x6cm DS*         1 Green or Orange 8 SMD 2 Strips   3 Strips For  Vias   1   1 SMD 1 SMD       SMD FROM HALL ROAD    
  11 Introduction to Negative / Positive Photo resist Method for PCB                                                   
  12 Introduction to De-soldering & usage of Hot Air Gun for SMD Components                                                  
  12 (b) 32pin & 64pin TQFP Package  Soldered on Adapter and then desoldered         1             5 Strips               1 1 1      
  13 Introduction to Relays (5V & 12V) with PCB footprint, usage and Driver       3x4cm                                          
  14 Introduction to Magnetic Contactor & Different Actuators                                                  
  15 Introduction to House hold Wiring for Single Pole one way and two way switches Scheme including UPS wiring schemes as well                                                  
  16 Project based on different Dot Matrix or Bar Display or Seven Segment or CFL PCB or Actuators on a Double sided PCB                                                  
 
 
# Buy more in case its burnt  
 
  Still Incomplete (Don't buy still)  
 
 
  Complete (Buy)